Airsoft Ohio Forums  
  #1  
Old 02-05-2013, 12:40 PM
Nytemayr's Avatar
Nytemayr Nytemayr is offline
Registered User
 
Join Date: Jun 2012
Location: Buford
Posts: 41
Nytemayr is a Private
iTrader: (0)
Post upgrade G&G M4 gearbox lockup

I just upgraded my stock G&G Combat Machine 16 Raider with a Matrix M115 spring. When I fired it, the gun barely cycled the first time and locked up the second time. As I was taking out the stock bolt, I heard a click, like something had released, so I test fired it again. It fired multiple times but sounded a little rough. Every time I tighten the stock bolt down all the way it won't fire and when I unsrew it a little bit, it will fire. Any hints?

Info
Gun - http://http://www.evike.com/product_...ducts_id=33557
Spring - http://http://www.evike.com/product_...ducts_id=31456
Battery - 7.4v 1200mAh 15-25c Lipo bought @ 321Airsoft a month ago
Reply With Quote
  #2  
Old 02-05-2013, 01:14 PM
sakujosei's Avatar
sakujosei sakujosei is offline
Registered User
 
Join Date: Dec 2011
Posts: 143
sakujosei is a Private
iTrader: (4)
the order you reassemble your gun can sometimes cause the gearbox to jack up which can push the motor out of alignment especially if the grip isn't aligned with the motor. The adjustment screw needs to be centered. My suggestion would be to assemble the gun in this order.

Rear body pin, mag-catch, rear stock (while putting on the rear stock push the mag-catch if its getting resistance your gearbox is jacking up a bit, as soon as you get resistance stop screwing in the stock), then start screwing in the grip until the mag-catch feels like it goes in and out freely, use that mag catch as your guide to see if the gearbox is getting jacked up too much or too low, it will show as resistance on the catch. tighten and and loosen screws in the stock and grip until everything feels secure, then put in the motor and end plate to the grip (make sure to align them), magpul grips are the easiest to do this with because you can unscrew the motor height screw and see if the motor shifted... other then that, maybe bad shim job?
Reply With Quote
  #3  
Old 02-19-2013, 01:11 PM
Nytemayr's Avatar
Nytemayr Nytemayr is offline
Registered User
 
Join Date: Jun 2012
Location: Buford
Posts: 41
Nytemayr is a Private
iTrader: (0)
SOLVED! The spring guide was not aligned. !Mods please delete!

Last edited by Nytemayr; 04-17-2013 at 07:48 AM. Reason: delete
Reply With Quote
Reply

Tags
g&g m4, gearbox, problem, spring

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
WTS: Inokatsu M60e3!!! / G&G M4 / M4 parts! CStahl Electric-Powered Weaponry 8 01-16-2011 08:48 AM
WTS/WTT: G&G M4, G&P M16, KWA MP7, and more tango91 Electric-Powered Weaponry 3 01-13-2011 11:15 AM
WTB: m4 lower and gearbox SpecialOp7 Electric-Powered Weaponry 1 12-20-2010 03:13 PM
WTB - Broken M4 - M4 Sans Gearbox tombo131 Electric-Powered Weaponry 0 12-12-2010 03:02 AM
AEG Mini-Guide, Prices, Gearbox Information, etc. Loki Newbie FAQ 2 04-21-2007 11:55 PM


All times are GMT -5. The time now is 03:00 AM.


Airsoft Guns, Tactical Gear, Military Gear, Ohio Airsoft Retailer

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Copyright 2005 - 2009 Airsoft Ohio